Add config for my printer

Configuration.h

@@ -60,7 +60,7 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
+#define STRING_CONFIG_H_AUTHOR "(sqozz, Tevo Tarantula)" // Who made the changes.
 //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
 
 /**
@@ -87,7 +87,7 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #define MOTHERBOARD BOARD_MKS_BASE_14
 #endif
 
 /**
@@ -135,7 +135,7 @@
 //#define BLUETOOTH
 
 // Name displayed in the LCD "Ready" message and Info menu
-//#define CUSTOM_MACHINE_NAME "3D Printer"
+#define CUSTOM_MACHINE_NAME "Am sqozz sei TEVO"
 
 // Printer's unique ID, used by some programs to differentiate between machines.
 // Choose your own or use a service like https://www.uuidgenerator.net/version4
@@ -536,7 +536,7 @@
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  *
  */
-#define TEMP_SENSOR_0 1
+#define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
@@ -544,7 +544,7 @@
 #define TEMP_SENSOR_5 0
 #define TEMP_SENSOR_6 0
 #define TEMP_SENSOR_7 0
-#define TEMP_SENSOR_BED 0
+#define TEMP_SENSOR_BED 1
 #define TEMP_SENSOR_PROBE 0
 #define TEMP_SENSOR_CHAMBER 0
 #define TEMP_SENSOR_COOLER 0
@@ -734,7 +734,7 @@
  * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  * @section bed temp
  */
-//#define PIDTEMPBED
+#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
@@ -752,9 +752,9 @@
 
   // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKp 984.88
-  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKi 193.91
-  #define DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKd 1250.55
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED
@@ -852,8 +852,8 @@
 
 #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
 #define THERMAL_PROTECTION_BED     // Enable thermal protection for the heated bed
-#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+//#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
-#define THERMAL_PROTECTION_COOLER  // Enable thermal protection for the laser cooling
+//#define THERMAL_PROTECTION_COOLER  // Enable thermal protection for the laser cooling
 
 //===========================================================================
 //============================= Mechanical Settings =========================
@@ -915,7 +915,7 @@
   #endif
 
   // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+  #define PRINTABLE_RADIUS       140.0    // (mm)
 
   // Maximum reachable area
   #define DELTA_MAX_RADIUS       140.0    // (mm)
@@ -969,7 +969,7 @@
   #if ENABLED(MORGAN_SCARA)
 
     //#define DEBUG_SCARA_KINEMATICS
-    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+    #define FEEDRATE_SCALING        // Convert XY feedrate from mm/s to degrees/s on the fly
 
     // Radius around the center where the arm cannot reach
     #define MIDDLE_DEAD_ZONE_R   0  // (mm)
@@ -1004,7 +1004,7 @@
   #define TPARA_OFFSET_Y    0       // (mm)
   #define TPARA_OFFSET_Z    0       // (mm)
 
-  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+  #define FEEDRATE_SCALING        // Convert XY feedrate from mm/s to degrees/s on the fly
 
   // Radius around the center where the arm cannot reach
   #define MIDDLE_DEAD_ZONE_R   0  // (mm)
@@ -1102,9 +1102,9 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
 #define I_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define J_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define K_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
@@ -1168,14 +1168,14 @@
  * Override with M92
  *                                      X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 500 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 1600, 100 }
 
 /**
  * Default Max Feed Rate (linear=mm/s, rotational=°/s)
  * Override with M203
  *                                      X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_FEEDRATE          { 300, 300, 5, 25 }
+#define DEFAULT_MAX_FEEDRATE          { 300, 300, 7, 50 }
 
 //#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
 #if ENABLED(LIMITED_MAX_FR_EDITING)
@@ -1331,7 +1331,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-//#define BLTOUCH
+#define BLTOUCH
 
 /**
  * MagLev V4 probe by MDD
@@ -1420,13 +1420,13 @@
   // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
   // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
 
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, PRINTABLE_RADIUS, 100.0 }
   #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
 
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, PRINTABLE_RADIUS, 100.0 }
   #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
 
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (PRINTABLE_RADIUS) * 0.75, 100.0 }
   #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
 
   #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
@@ -1483,7 +1483,9 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
+
+//Offsets: X -31, Y -35, Z -2.75
+#define NOZZLE_TO_PROBE_OFFSET { -31, -35, -2.75 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
@@ -1641,7 +1643,7 @@
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
 #define INVERT_X_DIR false
-#define INVERT_Y_DIR true
+#define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 //#define INVERT_I_DIR false
 //#define INVERT_J_DIR false
@@ -1703,7 +1705,7 @@
 #define Z_MIN_POS 0
 #define X_MAX_POS X_BED_SIZE
 #define Y_MAX_POS Y_BED_SIZE
-#define Z_MAX_POS 200
+#define Z_MAX_POS 184
 //#define I_MIN_POS 0
 //#define I_MAX_POS 50
 //#define J_MIN_POS 0
@@ -1755,7 +1757,7 @@
 #endif
 
 #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
-  //#define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
+  #define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
 #endif
 
 /**
@@ -1874,7 +1876,7 @@
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
 //#define AUTO_BED_LEVELING_BILINEAR
-//#define AUTO_BED_LEVELING_UBL
+#define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 
 /**
@@ -1882,7 +1884,7 @@
  * these options to restore the prior leveling state or to always enable
  * leveling immediately after G28.
  */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
 //#define ENABLE_LEVELING_AFTER_G28
 
 /**
@@ -1937,12 +1939,12 @@
   /**
    * Enable the G26 Mesh Validation Pattern tool.
    */
-  //#define G26_MESH_VALIDATION
+  #define G26_MESH_VALIDATION
   #if ENABLED(G26_MESH_VALIDATION)
     #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
     #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for G26.
-    #define MESH_TEST_HOTEND_TEMP  205    // (°C) Default nozzle temperature for G26.
+    #define MESH_TEST_HOTEND_TEMP  210    // (°C) Default nozzle temperature for G26.
-    #define MESH_TEST_BED_TEMP      60    // (°C) Default bed temperature for G26.
+    #define MESH_TEST_BED_TEMP      70    // (°C) Default bed temperature for G26.
     #define G26_XY_FEEDRATE         20    // (mm/s) Feedrate for G26 XY moves.
     #define G26_XY_FEEDRATE_TRAVEL 100    // (mm/s) Feedrate for G26 XY travel moves.
     #define G26_RETRACT_MULTIPLIER   1.0  // G26 Q (retraction) used by default between mesh test elements.
@@ -2090,7 +2092,7 @@
  * - Allows Z homing only when XY positions are known and trusted.
  * - If stepper drivers sleep, XY homing may be required again before Z homing.
  */
-//#define Z_SAFE_HOMING
+#define Z_SAFE_HOMING
 
 #if ENABLED(Z_SAFE_HOMING)
   #define Z_SAFE_HOMING_X_POINT X_CENTER  // X point for Z homing
@@ -2176,13 +2178,13 @@
  *   M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  *   M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  */
-//#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
+#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
 //#define DISABLE_M503        // Saves ~2700 bytes of flash. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save PROGMEM.
 #define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
 #if ENABLED(EEPROM_SETTINGS)
-  //#define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
+  #define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
-  //#define EEPROM_INIT_NOW   // Init EEPROM on first boot after a new build.
+  #define EEPROM_INIT_NOW   // Init EEPROM on first boot after a new build.
 #endif
 
 // @section host
@@ -2215,10 +2217,10 @@
 // Preheat Constants - Up to 10 are supported without changes
 //
 #define PREHEAT_1_LABEL       "PLA"
-#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_HOTEND 200
 #define PREHEAT_1_TEMP_BED     70
 #define PREHEAT_1_TEMP_CHAMBER 35
-#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
 #define PREHEAT_2_TEMP_HOTEND 240
@@ -2239,7 +2241,7 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
@@ -2368,7 +2370,7 @@
  *
  * View the current statistics with M78.
  */
-//#define PRINTCOUNTER
+#define PRINTCOUNTER
 #if ENABLED(PRINTCOUNTER)
   #define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print. A value of 0 will save stats at end of print.
 #endif
@@ -2461,7 +2463,7 @@
  * SD Card support is disabled by default. If your controller has an SD slot,
  * you must uncomment the following option or it won't work.
  */
-//#define SDSUPPORT
+#define SDSUPPORT
 
 /**
  * SD CARD: ENABLE CRC
@@ -2485,13 +2487,13 @@
 // This option overrides the default number of encoder pulses needed to
 // produce one step. Should be increased for high-resolution encoders.
 //
-//#define ENCODER_PULSES_PER_STEP 4
+#define ENCODER_PULSES_PER_STEP 4
 
 //
 // Use this option to override the number of step signals required to
 // move between next/prev menu items.
 //
-//#define ENCODER_STEPS_PER_MENU_ITEM 1
+#define ENCODER_STEPS_PER_MENU_ITEM 1
 
 /**
  * Encoder Direction Options
@@ -2508,7 +2510,7 @@
 //
 //  Set this option if CLOCKWISE causes values to DECREASE
 //
-//#define REVERSE_ENCODER_DIRECTION
+#define REVERSE_ENCODER_DIRECTION
 
 //
 // This option reverses the encoder direction for navigating LCD menus.
@@ -2541,8 +2543,8 @@
 //
 // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
 //
-//#define INDIVIDUAL_AXIS_HOMING_MENU
+#define INDIVIDUAL_AXIS_HOMING_MENU
-//#define INDIVIDUAL_AXIS_HOMING_SUBMENU
+#define INDIVIDUAL_AXIS_HOMING_SUBMENU
 
 //
 // SPEAKER/BUZZER
@@ -2559,8 +2561,8 @@
 // Note: Test audio output with the G-Code:
 //  M300 S<frequency Hz> P<duration ms>
 //
-//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
+#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
-//#define LCD_FEEDBACK_FREQUENCY_HZ 5000
+#define LCD_FEEDBACK_FREQUENCY_HZ 5000
 
 //=============================================================================
 //======================== LCD / Controller Selection =========================
@@ -2574,7 +2576,7 @@
 //
 // Note: Usually sold with a white PCB.
 //
-//#define REPRAP_DISCOUNT_SMART_CONTROLLER
+#define REPRAP_DISCOUNT_SMART_CONTROLLER
 
 //
 // GT2560 (YHCB2004) LCD Display

Configuration_adv.h

@@ -450,6 +450,9 @@
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
   #define AUTOTEMP_OLDWEIGHT    0.98  // Factor used to weight previous readings (0.0 < value < 1.0)
+  #define AUTOTEMP_MIN          210
+  #define AUTOTEMP_MAX          250
+  #define AUTOTEMP_FACTOR       0.1f
   // Turn on AUTOTEMP on M104/M109 by default using proportions set here
   //#define AUTOTEMP_PROPORTIONAL
   #if ENABLED(AUTOTEMP_PROPORTIONAL)
@@ -883,7 +886,7 @@
 //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 }  // (linear=mm, rotational=°) Backoff from endstops after homing
 //#define XY_COUNTERPART_BACKOFF_MM 0         // (mm) Backoff X after homing Y, and vice-versa
 
-//#define QUICK_HOME                          // If G28 contains XY do a diagonal move first
+#define QUICK_HOME                          // If G28 contains XY do a diagonal move first
 //#define HOME_Y_BEFORE_X                     // If G28 contains XY home Y before X
 //#define HOME_Z_FIRST                        // Home Z first. Requires a Z-MIN endstop (not a probe).
 //#define CODEPENDENT_XY_HOMING               // If X/Y can't home without homing Y/X first
@@ -1409,7 +1412,7 @@
   #endif
 
   // Include a page of printer information in the LCD Main Menu
-  //#define LCD_INFO_MENU
+  #define LCD_INFO_MENU
   #if ENABLED(LCD_INFO_MENU)
     //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
   #endif
@@ -1432,14 +1435,14 @@
   //#define LCD_TIMEOUT_TO_STATUS 15000   // (ms)
 
   #if ENABLED(SHOW_BOOTSCREEN)
-    #define BOOTSCREEN_TIMEOUT 4000       // (ms) Total Duration to display the boot screen(s)
+    #define BOOTSCREEN_TIMEOUT 1000       // (ms) Total Duration to display the boot screen(s)
     #if EITHER(HAS_MARLINUI_U8GLIB, TFT_COLOR_UI)
       #define BOOT_MARLIN_LOGO_SMALL      // Show a smaller Marlin logo on the Boot Screen (saving lots of flash)
     #endif
   #endif
 
   // Scroll a longer status message into view
-  //#define STATUS_MESSAGE_SCROLLING
+  #define STATUS_MESSAGE_SCROLLING
 
   // Apply a timeout to low-priority status messages
   //#define STATUS_MESSAGE_TIMEOUT_SEC 30 // (seconds)