Add config for my printer
This commit is contained in:
parent
0c96911ae0
commit
826f4e6ea5
100
Configuration.h
100
Configuration.h
|
|
@ -60,7 +60,7 @@
|
|||
// @section info
|
||||
|
||||
// Author info of this build printed to the host during boot and M115
|
||||
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
|
||||
#define STRING_CONFIG_H_AUTHOR "(sqozz, Tevo Tarantula)" // Who made the changes.
|
||||
//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
|
||||
|
||||
/**
|
||||
|
|
@ -87,7 +87,7 @@
|
|||
|
||||
// Choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_RAMPS_14_EFB
|
||||
#define MOTHERBOARD BOARD_MKS_BASE_14
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -135,7 +135,7 @@
|
|||
//#define BLUETOOTH
|
||||
|
||||
// Name displayed in the LCD "Ready" message and Info menu
|
||||
//#define CUSTOM_MACHINE_NAME "3D Printer"
|
||||
#define CUSTOM_MACHINE_NAME "Am sqozz sei TEVO"
|
||||
|
||||
// Printer's unique ID, used by some programs to differentiate between machines.
|
||||
// Choose your own or use a service like https://www.uuidgenerator.net/version4
|
||||
|
|
@ -536,7 +536,7 @@
|
|||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
|
|
@ -544,7 +544,7 @@
|
|||
#define TEMP_SENSOR_5 0
|
||||
#define TEMP_SENSOR_6 0
|
||||
#define TEMP_SENSOR_7 0
|
||||
#define TEMP_SENSOR_BED 0
|
||||
#define TEMP_SENSOR_BED 1
|
||||
#define TEMP_SENSOR_PROBE 0
|
||||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
|
|
@ -734,7 +734,7 @@
|
|||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
* @section bed temp
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
|
|
@ -752,9 +752,9 @@
|
|||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
#define DEFAULT_bedKp 10.00
|
||||
#define DEFAULT_bedKi .023
|
||||
#define DEFAULT_bedKd 305.4
|
||||
#define DEFAULT_bedKp 984.88
|
||||
#define DEFAULT_bedKi 193.91
|
||||
#define DEFAULT_bedKd 1250.55
|
||||
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
#endif // PIDTEMPBED
|
||||
|
|
@ -852,8 +852,8 @@
|
|||
|
||||
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
|
||||
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
|
||||
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
|
||||
#define THERMAL_PROTECTION_COOLER // Enable thermal protection for the laser cooling
|
||||
//#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
|
||||
//#define THERMAL_PROTECTION_COOLER // Enable thermal protection for the laser cooling
|
||||
|
||||
//===========================================================================
|
||||
//============================= Mechanical Settings =========================
|
||||
|
|
@ -915,7 +915,7 @@
|
|||
#endif
|
||||
|
||||
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
|
||||
#define DELTA_PRINTABLE_RADIUS 140.0 // (mm)
|
||||
#define PRINTABLE_RADIUS 140.0 // (mm)
|
||||
|
||||
// Maximum reachable area
|
||||
#define DELTA_MAX_RADIUS 140.0 // (mm)
|
||||
|
|
@ -969,7 +969,7 @@
|
|||
#if ENABLED(MORGAN_SCARA)
|
||||
|
||||
//#define DEBUG_SCARA_KINEMATICS
|
||||
#define SCARA_FEEDRATE_SCALING // Convert XY feedrate from mm/s to degrees/s on the fly
|
||||
#define FEEDRATE_SCALING // Convert XY feedrate from mm/s to degrees/s on the fly
|
||||
|
||||
// Radius around the center where the arm cannot reach
|
||||
#define MIDDLE_DEAD_ZONE_R 0 // (mm)
|
||||
|
|
@ -1004,7 +1004,7 @@
|
|||
#define TPARA_OFFSET_Y 0 // (mm)
|
||||
#define TPARA_OFFSET_Z 0 // (mm)
|
||||
|
||||
#define SCARA_FEEDRATE_SCALING // Convert XY feedrate from mm/s to degrees/s on the fly
|
||||
#define FEEDRATE_SCALING // Convert XY feedrate from mm/s to degrees/s on the fly
|
||||
|
||||
// Radius around the center where the arm cannot reach
|
||||
#define MIDDLE_DEAD_ZONE_R 0 // (mm)
|
||||
|
|
@ -1102,9 +1102,9 @@
|
|||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define I_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define J_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define K_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
|
|
@ -1168,14 +1168,14 @@
|
|||
* Override with M92
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 500 }
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 1600, 100 }
|
||||
|
||||
/**
|
||||
* Default Max Feed Rate (linear=mm/s, rotational=°/s)
|
||||
* Override with M203
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
|
||||
#define DEFAULT_MAX_FEEDRATE { 300, 300, 7, 50 }
|
||||
|
||||
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
|
||||
#if ENABLED(LIMITED_MAX_FR_EDITING)
|
||||
|
|
@ -1331,7 +1331,7 @@
|
|||
/**
|
||||
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
|
||||
*/
|
||||
//#define BLTOUCH
|
||||
#define BLTOUCH
|
||||
|
||||
/**
|
||||
* MagLev V4 probe by MDD
|
||||
|
|
@ -1420,13 +1420,13 @@
|
|||
// 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
|
||||
// if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
|
||||
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, PRINTABLE_RADIUS, 100.0 }
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
|
||||
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, PRINTABLE_RADIUS, 100.0 }
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
|
||||
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (PRINTABLE_RADIUS) * 0.75, 100.0 }
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
|
||||
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
|
||||
|
|
@ -1483,7 +1483,9 @@
|
|||
* | [-] |
|
||||
* O-- FRONT --+
|
||||
*/
|
||||
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
|
||||
|
||||
//Offsets: X -31, Y -35, Z -2.75
|
||||
#define NOZZLE_TO_PROBE_OFFSET { -31, -35, -2.75 }
|
||||
|
||||
// Most probes should stay away from the edges of the bed, but
|
||||
// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
|
||||
|
|
@ -1641,7 +1643,7 @@
|
|||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_Y_DIR false
|
||||
#define INVERT_Z_DIR false
|
||||
//#define INVERT_I_DIR false
|
||||
//#define INVERT_J_DIR false
|
||||
|
|
@ -1703,7 +1705,7 @@
|
|||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS X_BED_SIZE
|
||||
#define Y_MAX_POS Y_BED_SIZE
|
||||
#define Z_MAX_POS 200
|
||||
#define Z_MAX_POS 184
|
||||
//#define I_MIN_POS 0
|
||||
//#define I_MAX_POS 50
|
||||
//#define J_MIN_POS 0
|
||||
|
|
@ -1755,7 +1757,7 @@
|
|||
#endif
|
||||
|
||||
#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
|
||||
//#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
|
||||
#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -1874,7 +1876,7 @@
|
|||
//#define AUTO_BED_LEVELING_3POINT
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
#define AUTO_BED_LEVELING_UBL
|
||||
//#define MESH_BED_LEVELING
|
||||
|
||||
/**
|
||||
|
|
@ -1882,7 +1884,7 @@
|
|||
* these options to restore the prior leveling state or to always enable
|
||||
* leveling immediately after G28.
|
||||
*/
|
||||
//#define RESTORE_LEVELING_AFTER_G28
|
||||
#define RESTORE_LEVELING_AFTER_G28
|
||||
//#define ENABLE_LEVELING_AFTER_G28
|
||||
|
||||
/**
|
||||
|
|
@ -1937,12 +1939,12 @@
|
|||
/**
|
||||
* Enable the G26 Mesh Validation Pattern tool.
|
||||
*/
|
||||
//#define G26_MESH_VALIDATION
|
||||
#define G26_MESH_VALIDATION
|
||||
#if ENABLED(G26_MESH_VALIDATION)
|
||||
#define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
|
||||
#define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for G26.
|
||||
#define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for G26.
|
||||
#define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for G26.
|
||||
#define MESH_TEST_HOTEND_TEMP 210 // (°C) Default nozzle temperature for G26.
|
||||
#define MESH_TEST_BED_TEMP 70 // (°C) Default bed temperature for G26.
|
||||
#define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for G26 XY moves.
|
||||
#define G26_XY_FEEDRATE_TRAVEL 100 // (mm/s) Feedrate for G26 XY travel moves.
|
||||
#define G26_RETRACT_MULTIPLIER 1.0 // G26 Q (retraction) used by default between mesh test elements.
|
||||
|
|
@ -2090,7 +2092,7 @@
|
|||
* - Allows Z homing only when XY positions are known and trusted.
|
||||
* - If stepper drivers sleep, XY homing may be required again before Z homing.
|
||||
*/
|
||||
//#define Z_SAFE_HOMING
|
||||
#define Z_SAFE_HOMING
|
||||
|
||||
#if ENABLED(Z_SAFE_HOMING)
|
||||
#define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing
|
||||
|
|
@ -2176,13 +2178,13 @@
|
|||
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
//#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of flash. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
|
||||
#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
//#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
|
||||
//#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build.
|
||||
#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
|
||||
#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build.
|
||||
#endif
|
||||
|
||||
// @section host
|
||||
|
|
@ -2215,10 +2217,10 @@
|
|||
// Preheat Constants - Up to 10 are supported without changes
|
||||
//
|
||||
#define PREHEAT_1_LABEL "PLA"
|
||||
#define PREHEAT_1_TEMP_HOTEND 180
|
||||
#define PREHEAT_1_TEMP_HOTEND 200
|
||||
#define PREHEAT_1_TEMP_BED 70
|
||||
#define PREHEAT_1_TEMP_CHAMBER 35
|
||||
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
|
||||
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
|
||||
|
||||
#define PREHEAT_2_LABEL "ABS"
|
||||
#define PREHEAT_2_TEMP_HOTEND 240
|
||||
|
|
@ -2239,7 +2241,7 @@
|
|||
* P1 Raise the nozzle always to Z-park height.
|
||||
* P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
|
||||
*/
|
||||
//#define NOZZLE_PARK_FEATURE
|
||||
#define NOZZLE_PARK_FEATURE
|
||||
|
||||
#if ENABLED(NOZZLE_PARK_FEATURE)
|
||||
// Specify a park position as { X, Y, Z_raise }
|
||||
|
|
@ -2368,7 +2370,7 @@
|
|||
*
|
||||
* View the current statistics with M78.
|
||||
*/
|
||||
//#define PRINTCOUNTER
|
||||
#define PRINTCOUNTER
|
||||
#if ENABLED(PRINTCOUNTER)
|
||||
#define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print. A value of 0 will save stats at end of print.
|
||||
#endif
|
||||
|
|
@ -2461,7 +2463,7 @@
|
|||
* SD Card support is disabled by default. If your controller has an SD slot,
|
||||
* you must uncomment the following option or it won't work.
|
||||
*/
|
||||
//#define SDSUPPORT
|
||||
#define SDSUPPORT
|
||||
|
||||
/**
|
||||
* SD CARD: ENABLE CRC
|
||||
|
|
@ -2485,13 +2487,13 @@
|
|||
// This option overrides the default number of encoder pulses needed to
|
||||
// produce one step. Should be increased for high-resolution encoders.
|
||||
//
|
||||
//#define ENCODER_PULSES_PER_STEP 4
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
|
||||
//
|
||||
// Use this option to override the number of step signals required to
|
||||
// move between next/prev menu items.
|
||||
//
|
||||
//#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
|
||||
/**
|
||||
* Encoder Direction Options
|
||||
|
|
@ -2508,7 +2510,7 @@
|
|||
//
|
||||
// Set this option if CLOCKWISE causes values to DECREASE
|
||||
//
|
||||
//#define REVERSE_ENCODER_DIRECTION
|
||||
#define REVERSE_ENCODER_DIRECTION
|
||||
|
||||
//
|
||||
// This option reverses the encoder direction for navigating LCD menus.
|
||||
|
|
@ -2541,8 +2543,8 @@
|
|||
//
|
||||
// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
|
||||
//
|
||||
//#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
//#define INDIVIDUAL_AXIS_HOMING_SUBMENU
|
||||
#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
#define INDIVIDUAL_AXIS_HOMING_SUBMENU
|
||||
|
||||
//
|
||||
// SPEAKER/BUZZER
|
||||
|
|
@ -2559,8 +2561,8 @@
|
|||
// Note: Test audio output with the G-Code:
|
||||
// M300 S<frequency Hz> P<duration ms>
|
||||
//
|
||||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
|
||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 5000
|
||||
#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
|
||||
#define LCD_FEEDBACK_FREQUENCY_HZ 5000
|
||||
|
||||
//=============================================================================
|
||||
//======================== LCD / Controller Selection =========================
|
||||
|
|
@ -2574,7 +2576,7 @@
|
|||
//
|
||||
// Note: Usually sold with a white PCB.
|
||||
//
|
||||
//#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
||||
#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
||||
|
||||
//
|
||||
// GT2560 (YHCB2004) LCD Display
|
||||
|
|
|
|||
|
|
@ -450,6 +450,9 @@
|
|||
#define AUTOTEMP
|
||||
#if ENABLED(AUTOTEMP)
|
||||
#define AUTOTEMP_OLDWEIGHT 0.98 // Factor used to weight previous readings (0.0 < value < 1.0)
|
||||
#define AUTOTEMP_MIN 210
|
||||
#define AUTOTEMP_MAX 250
|
||||
#define AUTOTEMP_FACTOR 0.1f
|
||||
// Turn on AUTOTEMP on M104/M109 by default using proportions set here
|
||||
//#define AUTOTEMP_PROPORTIONAL
|
||||
#if ENABLED(AUTOTEMP_PROPORTIONAL)
|
||||
|
|
@ -883,7 +886,7 @@
|
|||
//#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (linear=mm, rotational=°) Backoff from endstops after homing
|
||||
//#define XY_COUNTERPART_BACKOFF_MM 0 // (mm) Backoff X after homing Y, and vice-versa
|
||||
|
||||
//#define QUICK_HOME // If G28 contains XY do a diagonal move first
|
||||
#define QUICK_HOME // If G28 contains XY do a diagonal move first
|
||||
//#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X
|
||||
//#define HOME_Z_FIRST // Home Z first. Requires a Z-MIN endstop (not a probe).
|
||||
//#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first
|
||||
|
|
@ -1409,7 +1412,7 @@
|
|||
#endif
|
||||
|
||||
// Include a page of printer information in the LCD Main Menu
|
||||
//#define LCD_INFO_MENU
|
||||
#define LCD_INFO_MENU
|
||||
#if ENABLED(LCD_INFO_MENU)
|
||||
//#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
|
||||
#endif
|
||||
|
|
@ -1432,14 +1435,14 @@
|
|||
//#define LCD_TIMEOUT_TO_STATUS 15000 // (ms)
|
||||
|
||||
#if ENABLED(SHOW_BOOTSCREEN)
|
||||
#define BOOTSCREEN_TIMEOUT 4000 // (ms) Total Duration to display the boot screen(s)
|
||||
#define BOOTSCREEN_TIMEOUT 1000 // (ms) Total Duration to display the boot screen(s)
|
||||
#if EITHER(HAS_MARLINUI_U8GLIB, TFT_COLOR_UI)
|
||||
#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving lots of flash)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// Scroll a longer status message into view
|
||||
//#define STATUS_MESSAGE_SCROLLING
|
||||
#define STATUS_MESSAGE_SCROLLING
|
||||
|
||||
// Apply a timeout to low-priority status messages
|
||||
//#define STATUS_MESSAGE_TIMEOUT_SEC 30 // (seconds)
|
||||
|
|
|
|||
Loading…
Reference in a new issue